Vision Multi Axis Specifikace Strana 1

Multi Axis Engraver Operations Manual Vision Engraving & Routing Systems 17621 N. Black Canyon Hwy. Phoenix, AZ 85023 www.visioneng

10 Multi Axis Engraver Operating Manual

Chapter 3 - Operations 11 Chapter 3 - Operations Machine Description & Terminology This chapter briefly describes the major components of

12 Multi Axis Engraver Operating Manual 10) Vice Tightening Handle - Turning this handle clockwise will tighten the vice and turning this handl

Chapter 3 - Operations 13 (Figure 3.2) The MAX Engraver components See Figure 3.3 below 1) Head Stock - This is where objects to be rotary

14 Multi Axis Engraver Operating Manual (Figure 3.4) The optional T-Slot table Flat Engraving Flat Objects - Initial Setup When setting up to

Chapter 3 - Operations 15 3) If the distance is greater than 1 1/2”, loosen the height adjustment screw shown below in figure 3.6. Then r

16 Multi Axis Engraver Operating Manual (Figure 3.7) Lowering the spindle into the clamp 5) Loosen the vice slide adjustment screw shown be

Chapter 3 - Operations 17 Plates Clamping plates such as name badges, desk plates and trophy plates are very easy on the MAX Engraver. Open t

18 Multi Axis Engraver Operating Manual Insert the pen into the V shaped opening in the side of the pen & medallion jig and tighten the cl

Chapter 3 - Operations 19 4) Press the Y jog buttons on the Vision Series 3 Controller to move the spindle towards the center of the object

Copyright  2005 Vision Computerized Engraving & Routing Systems (A Division of Western Engravers Supply, Inc.) All Rights Reserved This pub

20 Multi Axis Engraver Operating Manual 7) Move the object you are engraving forwards or backwards until the center of the object directly b

Chapter 3 - Operations 21 Once the locking screw is tightened, re-tighten the tilt adjustment knob shown in figure 3.15 above. Next, adjus

22 Multi Axis Engraver Operating Manual Next, loosen the tilt adjustment lock screw shown below in figure 3.18 screws approximately 1 turn.

Chapter 3 - Operations 23 When you send a job to the engraver from Vision, make sure that you select the MaxR machine driver and when you send

24 Multi Axis Engraver Operating Manual Turn the Vision Series 3 Controller on by flipping the switch on the back right side of the machine. S

Chapter 3 - Operations 25 (Figure 3.22) The MAX Engraver spindle with rotary cutter Spindle PulleySpindle HousingPointerMicrometerRetainer R

26 Multi Axis Engraver Operating Manual of the nose cone touches the engraving material. Once the nose cone touches the material, press the Z

Chapter 3 - Operations 27 SpindlePulleySpindleHousingPointerMicrometerRetainerRingNoseCone Burnishing is different than standard rotary eng

28 Multi Axis Engraver Operating Manual machine is engraving. Now press start. The job should now engrave. If there are any problems, press

Chapter 3 - Operations 29 Turn the Vision Series 3 Controller on by flipping the switch on the back right side of the machine. Set up the

Table of Contents iii Table of Contents CHAPTER 1 - BEFORE YOU BEGIN 5 About This Manual ...

30 Multi Axis Engraver Operating Manual

Chapter 4 - Optional Accessories 31 Chapter 4 - Optional Accessories Clamping Devices Below are some optional clamping devices that may be nec

32 Multi Axis Engraver Operating Manual These jaws enable engraving on all types of pens and other small cylindrical objects. Rotating the j

Chapter 4 - Optional Accessories 33 Vacuum Chip Removal System The optional vacuum chip removal system is designed to simplify the engraving p

34 Multi Axis Engraver Operating Manual

Chapter 5 - Maintenance 35 Chapter 5 - Maintenance Removing Chips Vision strives for the highest quality in their manufacturing process to pro

36 Multi Axis Engraver Operating Manual Cleaning the Vacuum Filter (only with the vacuum chip removal option) On systems with a vacuum chip re

Chapter 5 - Maintenance 37 DO NOT use any lubricant other than silicone, as it may become sticky and cause a buildup that can cause mechanical

38 Multi Axis Engraver Operating Manual Changing the Motor Belt Over a period of time, the MAX Engraver motor belt will wear. When the motor b

Index 39 Index —A— About This Manual, 5 Angled Engraving, 21 —B— Burnish Engraving, 26 —C— Changing the Motor Belt, 38 Clamping Devices, 31 —E

iv Multi Axis Engraver Operating Manual CHAPTER 5 - MAINTENANCE 35 Removing Chips ...

40 Multi Axis Engraver Operating Manual

Index 41

Chapter 1 - Before You Begin 5 Chapter 1 - Before You Begin About This Manual This Manual is designed to provide you with information about yo

6 Multi Axis Engraver Operating Manual  Place the machine in a location with low humidity and a minimum of dust. Avoid placing the equipment

Chapter 2 - Installation 7 Chapter 2 - Installation Hooking up the table There are two connections that must be made on the MAX Engraver table

8 Multi Axis Engraver Operating Manual Locate the rotary axis cable that comes off the back of the MAX Engraver as shown in figure 2.3 below

Chapter 2 - Installation 9 The MAX Engraver is now ready to engrave.